TopsDecor.com Home Decor Ideas
Every element in your home can affect its appearance and functionality. It will be a challenge for you to enjoy indoors and feel comfortable when your home is in a mess. Such an ambience can also prevent you from making friends stay longer.
If you’re looking for a simple upgrade that can do wonders for the aesthetics of your home, replace your baseboards and window sills. Window sills can serve as additional storage space, prevent water from entering your walls, and provide structural support for your windows. Skirting boards, on the other hand, protect your walls from damage.
Replace your baseboards
Read below to replace your skirting boards:
- Remove your old baseboard with a hammer and chisel. Use these tools to carefully remove the baseboard from your walls. Do this step by step and maximize the chisel as you pull deeper from your walls.
- Before installing high-quality skirting boards from well-known service providers like that Skirting board shopMake sure the surfaces are dry, clean and free of dust, grease and oil. You should also sand the walls to remove uneven color lines or excess paint.
- Take your tape measure and measure the length of the first baseboard. When measuring between two walls, make sure the tape measure is attached to each wall, and then note the measurement in millimeters. To make it easier for you, write the measure on the wall and then add the length of the tape measure body.
- Take your baseboard and cut the molding based on the measured length. When cutting with a saw, make sure that both ends are at an angle of 45 degrees.
- Place the first molding on your wall. Make sure that one end is in the corner area and adjust the molding so that it fits perfectly in the other corner. Depending on the size of your walls and the weight of your molded part, you may have to perform several trials and mistakes in this task. When you are satisfied with the insertion of the ends, press the center of the molding against the wall.
- Nail the baseboard to your walls with masonry nails. Start with the middle of the baseboard and one nail every 20 cm. Align your nails at a 30-degree angle to ensure that not all skirting boards can be easily pulled away from your walls.
- Repeat steps 1 through 6 if you are installing baseboards on other walls around your home. Finish the project with a silicone sealer to seal open seams. All holes should also be covered with wooden fillers. These small retouches protect your baseboards and ensure that your walls get a high-quality look.
Replace your window sills
Follow these steps so that you can easily replace your window sills:
- Remove the inner window from your window pane from inside your home.
- Use the lever bar to carefully remove the window sills from the outside. If this is your first time, be as careful as possible to make sure your windowsills stay intact. When using a replacement, you can easily measure when cutting a spare part. Also make sure you bring a piece of wood from your windowsill to the hardware store so that you can easily discuss your options with a sales representative. If you want to use new materials, pre-treated wood is a good option as it can withstand harsh weather conditions.
- Measure your old window sills into a fresh piece of wood. It is important to take accurate measurements to ensure that the new windowsill fits the old one easily.
- Cut the wood to size using a table saw. Make sure to saw the wood precisely, as it will be difficult for you to install it in your windowsill if you cut it too small or too large.
- Lighten your new window sill. Depending on the size of the wood, this task can be done alone or with the help of other people. Secure your windowsill by nailing galvanized nails through the outside edge of your windowsill into the frame.
- If you see gaps or leaks, fill them in seal. This is one of the most important tasks when replacing your window sills, because if there are gaps and leaks, water can easily penetrate the wood and damage your window sills.
Start with the right foot
Replacing baseboards and window sills is an easy task. However, if this is your first time doing such projects, it is best to do your research and invest in the best materials before you start. Knowing the pros and cons of the processes and using high quality materials will help you swap out your baseboards and window sills and ensure that these projects take as long as possible!
